Intelix DIGI-VGASD2-T4 Bedienungsanleitung PDF herunterladen (Seite 2)

DIGI-VGASD2-T4 Installation Guide

8001 Terrace Ave

Suite 201

Middleton, WI 53562

Phone: 608-831-0880

Toll-Free: 866-4-MATMIX

Fax: 608-831-1833

Cable Pinouts:

Technical Specifications

Compatible Receivers

DIGI-VGASD2-R

Maximum Distance per Linked Unit

350 feet

Supported Video Resolutions

Up to 1920x1200

Supported Audio

Analog stereo audio (-10dBv)

EDID Modes

1280x800(WXGA) Preset, 1024x768(XGA) Preset, EDID

Copy

Video Bandwidth

300 MHz

Audio Frequency Response

20 Hz to 20 kHz +/- 1dB

Crosstalk

-70 dB @ 2 kHz with a +7 dB input

-65 dB @ 20 kHz with a +7 dB input

Signal to Noise Ratio

80 dB @ 7 dBu

Dip switch modes

Switch one: Toggle EDID presets

Switch two: EDID copy mode on/off

Required Cabling

Cat 5, Cat 5e, Cat 6, Cat 7 compatible

Unshielded Twisted Pair Maximum

Capacitance

20 pf/foot

Cable Impedance

100 ohms @ 1 MHz (24 gauge or lower solid)

Cable Attenuation

6.6 dB/1000 feet @ 1 MHz copper

Connectors

(1) Computer video input (HD15F)

(1) Computer video output (HD15F)

(1) Stereo audio input (3.5mm TRS)

(1) Stereo audio output (3.5mm TRS)

(1) IR input (3.5mm TRS)

(1) IR output (3.5mm TS)

(4) Twisted pair output (RJ45)

(1) RS232 input (3 pole euroblock)

(1) Power input (5.5mm coaxial power connector)

Enclosure

Aluminum (Painted Black)

Dimensions (Including connectors)

215mm x 117mm x 42mm (8-1/2” x 4-5/8” x 1-11/16”)

Dimensions (Including

connectors/ears)

242mm x 117mm x 42mm (9-1/2” x 4-5/8” x 1-11/16”)

Shipping Weight

2lbs. (0.9kg)

Power

12vDC 2A

Regulatory

CE, RoHS

ESD Protection

Yes

Diagnostic Indicators

Power LED

Warranty

2 years

What’s in the Box

(1) DIGI-VGASD2-T4

(1) 12vDC 2A Power Supply

(1) Installation Manual

(2) Mounting Brackets

Available Accessories (not included)

VGASD2-EYE – IR Receiver

VGASD2-EMT – IR Emitter

 Distances, picture and audio quality may be affected by cable grade,

cable quality, source and destination equipment, RF and electrical.

Important notice:

 Do not attempt to disassemble or alter

the extender housing. There are no user-

serviceable parts inside the unit. Doing so

will void your warranty.

 To minimize the possibility of equipment

damage from electrostatic discharge

(ESD), all source and destination

equipment must be powered off during

installation.

 Do not connect the extender to a

telecommunication outlet wired to

unrelated equipment. Doing so may

damage the unit or any connected

equipment. Ensure all connected twisted

pair cabling is straight-through (point-to-

point).

 Allow proper ventilation to reduce the

risk of thermal failure.

Twisted Pair

Wiring - Use

T568B wiring

for Cat5e/6

connection

between send

and receive

units.

RS232 Wiring:

Consult the

manual of the

control devices

to determine

which pins the

TX/RX signals are

carried on. Be

sure to ALWAYS

connect TX to RX

and RX to TX.

Troubleshooting tips:

1. Noisy Audio – Increase the

source volume

2. Horizontal scrolling video bars –

Ground loop problem - try lifting

or grounding the transmitter or

receiver (VGA capture nut is a

ground)

3. No video – Perform EDID copy on

transmitter, check Cat5 cable,

check source settings (is it on?)

1 2

Kommentare zu diesen Handbüchern

Keine Kommentare